international certification bodies for its quality system and environmental management system. E5jK-T Series. E5CK-T. E5AK-T/E5EK-T. 1/4 DIN. 1/8 DIN. Omron E5AK Controllers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Omron E5AK Controllers. E5AK-TAA AC Omron Automation and Safety Controllers PROCESS CONTROLLER datasheet, inventory, & pricing.

Author: Kazrahn Vokinos
Country: Namibia
Language: English (Spanish)
Genre: Photos
Published (Last): 9 August 2015
Pages: 332
PDF File Size: 7.68 Mb
ePub File Size: 18.22 Mb
ISBN: 113-3-90499-217-8
Downloads: 8523
Price: Free* [*Free Regsitration Required]
Uploader: Gardakree

Page J Output Unit Ratings and Characteristics Ratings and characteristics conform to the output unit mounted on the controller.

Omron E5AK-AA2-500 Processor/Controller

Make sure that the stop bit, data length, parity and baud rate of the host computer and the E5AK controller are matching. The following figures shows the effect on data s5ak passing through the digital filter. Page 7 This chapter introduces the E5AK. Controllers must not be closely mounted vertically or horizontally.

Function PV before passing through filter PV after passing through filter 0. Of these, only the alarm assigned as the output can be used. PID control, standard con- trol or heating and cooling control.

In other words, you cannot switch between the auto and manual operations by key operation. F Dead band E5sk dead band is set with the set point as its center. However, note that these parameters can not be set when the mul- ti-SP function is not selected. Dead band Hysteresis heat Page Operating Condition Restrictions The upper limit is set for the heating side positive valueand the lower limit is set for the cooling side negative value as shown in the follow- ing figure.


These parameters are valid when the power is turned ON again or Function when level 0 to 2 modes are switched. In this mode, you can set the communications conditions, transfer output and event input parameters omrpn match the type of option unit set in the controller.

OMRON E5AK User Manual

Page 66 1 Set output e5xk maximum. Enter text from picture: Alarms 1 to 3, 5: Use this end code to remedy errors that may occur. Machine automation controller nj-series cpu unit opc ua pages. Also, when the input type, temperature unit and scaling sensor range are changed, set point limiter is forcibly reset to the scaling sensor range.

Pay Attention to the Following when Installing this Controller F If you remove the controller from its case, never touch nor apply shock to the elec- tronic parts inside. SP setting lower limit to SP setting upper limit 0: Page Alarm 1 hysteresis Setting Alarm Type 3. D Setting up the E5AK The functions lmron this key change according to how long it is pressed.

Some parameters are not displayed depending on the protect mode setting and conditions of use.


In other words, a response frame is returned for each command frame sent. Page Set point Stable range Set to Memory error F Meaning Internal memory operation is in error. Page 3 Press the key to display [ ] 0mV calibration display. Alarm output functions are activated when the upper limit is exceeded. So, the user need not calibrate the E5AK controller during regular use.

Related Files:  RESOLUCION 1016 DE 1989 EBOOK

The heater burnout alarm is always OFF if the alarm is set to 0. Be sure to turn on the power supply to the load either before or simultaneously with the start of Temperature Controller opera- tion.

Omron E5AK-AA Processor/Controller | eBay

Page 31 Permissible load impedance: The following conventions are used to indicate and classify precautions in this manual. Though a shorter pulse period provides better control performance, the control period should be set taking the life expectancy of the output unit into consideration when the output unit is relay.

E5AK controller has been correctly calibrated. The display changes to [ ] 5 V calibration display.

Al- ways heed the information provided with them. Setting Up 2 Draw out the internal mechanism towards you holding both sides of the front panel. On the E5AK controller, only parameters that can be used are displayed. Conventions Used in This Manual J Omrno of Abbreviations Sometimes the following abbreviations are used in parameter names, figures and in text explanations.

If the key is pressed for less than one second, the parameters are switched. About The Displays Each press of this key switches between the auto and manual opera- tions.

Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual.